Electric solenoid valve 34 12v
These momentary push-button switches allow you to extend/retract cylinder or turn on/off hydraulic motors. You can purchase this valve with a spring-to-center rocker switch. Do you need a switch or do you want to provide your own?.Note: “D” spools cannot be used for operating hydraulic cylinders and “A” spools cannot be used to operate hydraulic motors. If you’re operating a hydraulic motor, you’ll need “D” spools for motor control. If you’re operating a hydraulic cylinder you’ll need to get “A” spools for double acting cylinders. Are you operating a hydraulic cylinder or a hydraulic motor?.If you have a closed-center system, you will tee into a pressure line to connect other valves. Note: You only need this on open-center hydraulic systems. (Examples include: Other Control Valves, Rear Remote Valve, Backhoe Valve, 3-Point Valve)? If so, you’ll need the power beyond adapter sleeve to provide pressure and flow to those valves. Do you have other valves downstream from this valve.NOTE: None of our valves have load-sensing capabilities. If you do have a closed-center system, you’ll need to get the closed center adapter plug. These valves are setup for use on open-center hydraulic systems. If you’re installing this on a tractor, please check, it will say under the hydraulics of the data sheet. Do you have an open-center hydraulic system?.The GPM flow may be printed on the pump itself. If installing on a tractor please check, it will say under the hydraulics – “Pump Flow” – of the data sheet. If not, then we have larger Z80 valves that can accommodate up to 21 GPM, and Z100 Valves if the flow is between 21 GPM and 27 GPM. Is the flow through this valve less than 13 GPM?.Will this Monoblock Solenoid Control Valve work for my application?įirstly, you’ll need to answer the following questions: 1 5′ Valve/extension Harness with 4 DIN connectors.1 Switch Box with two momentary rocker switches and 36″ Harness.Weatherproof enclosure and DIN connectors.Switch Box with two momentary rocker switches that springs automatically to the neutral position.N Port: #8 (1/2 – 14) G Thread (British Pipe Thread Parallel).A & B Work Ports: #8 SAE O-Ring (3/4”-16) Thread.Max Operating Pressure: P = 3625 PSI, T = 725 PSI, A & B = 4350 PSI.Adjustable Relief Valve Range: 1500 to 3625 PSI.Capable of closed center or Power Beyond(conversion plug required).Used for open center systems (Pump to Tank Flow).SAE O-Ring ports ensure solid seal and prevent blockages.High-tensile strength cast iron monoblock construction.Precision ground and hard chrome-plated spools assure a long life.A and B ports are open to Tank in neutral position.All spools are double acting with spring return to neutral position, D spool is designed for non-load holding applications such as motors and horizontal cylinders.A and B ports are closed to Tank in neutral position.All spools are double acting with spring return to neutral position, A spool works to control double acting cylinders.Operate Cylinders for Snow Plows (“A” Spools)Ī Spool (Controls Double Acting Cylinders).Operate hydraulic motors (“D” Spool Required): Brush Cutter, Snow Blower.Operate hydraulic cylinders (Double-Acting or Single-Acting): Grapples (Tilt/Raise Cylinders), Box Blade (Height Adjustment).Also, our monoblock valves possess power beyond capability (Power Beyond Adapter Sleeve is required SKU: P40-PB), as well as the ability to operate as a closed-center valve (Closed-Center Plug Required SKU: P40-CC). A hydraulic control valve serves as a common example for the loader valve on a tractor. The flow rate listed shows the maximum allowed GPM (Gallons Per Minute) that can be put through a valve. The number of cylinders or motors that a control valve can operate is dependent on the number of spools on a valve. These valves start and stop fluid flow into hydraulic cylinders or hydraulic motors. Hydraulic Monoblock Valves are a style of Hydraulic Control valve. Hydraulic Monoblock Solenoid Control Valve, 2 Spool, 13 GPM, 12V DC